Fuse boxes & consumer units · Derby

Fuse box replacement and consumer unit upgrades in Derby

Replace an old fuse box with a modern consumer unit, add capacity for a new circuit, or bring your protection up to current standards, for homes and businesses across Derbyshire, with a fixed quote and full certification.

Quote within 24 business hours: send photos or a short video of the job, with your name, on WhatsApp, or request a quote online.

●  Serving Derby since 2009

●  Fixed quotes

●  NAPIT registered

●  Certified to BS 7671

●  Serving Derby since 2009

●  NAPIT registered

●  Fixed quotes

●  Certified to BS 7671

Electrician testing breakers in a new consumer unit in Derby
Finance available on electrical work

Replacing fuse boxes in Derby

Your consumer unit (fuse box) is the hub of your electrical system, and an outdated or undersized one is both a safety risk and a practical limitation. A modern unit with RCD protection and individually rated breakers protects against faults far better and makes it easy to add circuits as your needs change.

Our NAPIT-registered electricians carry out full replacements and upgrades for homes and businesses across Derby and Derbyshire. We assess your existing system, explain what's needed and give you a fixed quote before any work begins.

Signs your fuse box needs attention

✓  Rewireable fuses instead of breakers

✓  No RCD protection

✓  Frequent tripping or blown fuses

✓  No spare ways for new circuits

✓  An EICR that recommends replacement

Types of consumer unit upgrade

Full replacement

The old fuse box comes out and a new consumer unit goes in, with RCD protection and correctly rated breakers for every circuit.

Partial upgrade

Extra capacity for a new circuit such as an EV charger, garden power or an extension.

Safety upgrade

Adding or replacing RCD or RCBO protection, and surge protection, on a unit that lacks adequate fault protection.

Why modern consumer units are safer

Traditional fuse boxes were designed for far lower demand than modern homes place on them. Where a blown fuse wire had to be replaced by hand, modern breakers trip and reset in seconds, and each circuit is protected independently, so a fault on one doesn't take out the rest of the property.

The biggest improvement is RCD protection. An RCD monitors the current and cuts the power within milliseconds if it detects the kind of imbalance that happens when current flows through a person or to earth. Old fuse boxes offer nothing equivalent.

Individually rated breakers also mean each circuit has the right protection for its load, rather than one fuse covering circuits with very different demands. If you still have rewireable fuses, an upgrade is one of the most cost-effective safety improvements you can make, and it's a common recommendation in EICR reports for older Derby properties.

Homeowner resetting a tripped circuit breaker in a modern consumer unit
Electrician wiring a new consumer unit for a Derby home

Upgrading for modern electrical demand

EV chargers, home offices, electric showers, induction hobs and heat pumps all draw significant load, often at the same time. An undersized or outdated unit trips frequently, limits what you can run and, at worst, creates a fire risk from overloaded circuits.

We design upgrades around your actual and planned use. If you're adding an EV charger, extending or fitting a new kitchen or bathroom, sorting the consumer unit at the same time is more efficient and more cost-effective.

For landlords, a consumer unit upgrade carried out alongside EICR remedial work brings the whole installation up to standard in one visit. If the wiring itself is old, see our rewiring page.

Consumer unit upgrade costs

Every property is different, so we confirm the price after looking at photos or your board. As a guide:

WorkTypical price
RCD/RCBO protection, where the board has space but lacks the right protection£40–£120 per device
Surge protection device (SPD)£70–£150
Partial consumer unit upgrade: extra ways, new breakers or upgraded protection£150–£350
Full consumer unit replacement for old fuse boxes, no RCD protection, limited capacity or signs of overheating£450–£750
Earthing and bonding upgrades to gas and water supplies£80–£250

Prices are for typical domestic work; larger or three-phase commercial boards are quoted after a survey. Finance is available for larger projects.

How a fuse box replacement works

1

Agree the position

We confirm where the new unit will go before work starts. Moving it affects the cable runs, so this is agreed at the outset.

2

Isolate and remove

The incoming supply is isolated safely, the old fuse box is removed and every circuit is disconnected.

3

Fit and connect

The new unit is mounted and each circuit connected to a correctly rated breaker, with RCD, RCBO and surge protection as required.

4

Test, label and certify

Every circuit is tested and clearly labelled, and you receive an Electrical Installation Certificate.

Certification and Part P

Consumer unit replacement is notifiable work under Part P of the Building Regulations, so it must be done by a qualified electrician registered with an approved scheme. We're NAPIT registered, so we self-certify the work and issue the certificate directly, with no separate building control inspection needed.

For businesses, we also upgrade distribution boards, add breakers and extend circuits with minimal disruption. See our commercial electrician page.

Every upgrade includes

✓  An assessment of your existing system

✓  A fixed quote before work starts

✓  Work to BS 7671 by NAPIT-registered electricians

✓  Clear labelling of every circuit

✓  An Electrical Installation Certificate

Fuse box and consumer unit FAQs

No. Consumer unit replacement is notifiable work under Part P of the Building Regulations and must be done by a competent person registered with an approved scheme such as NAPIT or NICEIC. We're NAPIT registered, so we self-certify the work and issue the Electrical Installation Certificate directly.

Old fuse boxes struggle with modern demand, which leads to frequent blown fuses and the temptation to fit the wrong fuse wire. They usually have no RCD protection, so there's nothing to cut the power quickly if current flows through a person, and their age increases the risk of overheating and fire.

Yes. All must meet UK standards, but build quality, ease of use, surge protection options and modular features vary. We fit reputable brands and explain the options when we quote.

Most replacements are completed within a few hours, with the power off for part of that time. We agree a time with you in advance.

Both can meet the regulations. An RCBO board protects each circuit individually, so one fault doesn't switch off a group of circuits. We recommend the right option for your property and budget.

We've served Derby since 2009, we're NAPIT registered, and we assess your system before giving a fixed quote, work to BS 7671 and issue full certification. As part of the Derbyshire Specialists Group, we can also coordinate making good and other trades.

Consumer unit upgrades across Derbyshire

We replace fuse boxes across Derby, including Mickleover, Littleover, Chaddesden, Oakwood and Spondon, and the wider county, including:

Get a quote for a fuse box replacement

Send us a photo of your fuse box and main fuse and tell us what you're planning, and we'll come back with clear advice and a fixed price.

West Point, 22 Brook St, Derby DE1 3TE

© 2026 All Rights Reserved | Derbyshire Electrical Specialists part of Derbyshire Specialists Group

Derbyshire Specialists Group Ltd is an Introducer Appointed Representative of Ideal Sales Solutions Ltd, t/a Ideal4Finance. Ideal Sales Solutions Ltd is a credit broker and not a lender (FRN 703401). Finance available subject to status. The rate offered is always provisional and will depend upon your personal circumstances, the loan amount and the term.